Logotipo Texsa, S.A.

TEXSELF 1,5

TEXSELF 1.5 is a self-adhesive, elastomeric mastic (SBS) waterproofing membrane, with a high mechanical performance polyethylene film finish on the upper side and an easily removable silicone film on the lower side.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
TEXSELF 1.5 is a membrane, in which the upper side acts as both a reinforcement and non-stick film. It is a high density, very stable, cross-laminated polyethylene film, with great tear resistance and magnificent mechanical properties.
· Extremely simple application: applies quickly, cleanly, and without the need for additional tools.
· Easy adherence to the substrate after applying the asphalt primer.
· Overlaps are carried out by simple contact and pressure.
· No blowtorch needed; TEXSELF 1.5 application only requires a brush, cutter and rubber roller.
· Safe to install; minimal risk of fires because no flame is used.
· Flexible membrane that easily absorbs the movements of the roof.
• Waterproofing of underground walls
• Waterproofing of non-drinkable water tanks
• Details flashing in pitched roofs
• Reinforcement of waterproofing on pitched roofs subject to filtering as a result of rain and wind, or the accumulation of snow or ice on roofs, especially lowpitch roofs and on gables.
• It can be used as both a underlay or reinforcement
layer for waterproofing systems with bituminous shingles.
• Capillarity barrier in partially buried walls to stop rising water
• As a vapour barrier in both conventional and deck roof systems.
· SUPPORT: The surface where it will be applied must be free of dust, loose or poorly adhered materials, oily or non-stick residue and any soil in general. It may be applied on concrete, wood and fretwork sheet supports; an adherence test must be conducted on all other surfaces.
· Primer: For better adherence of the membrane, apply EMUFAL I to the support, allowing to dry completely, approximately 24 hours. For flat and cohesive surfaces: metal, plastic, solid wood surfaces, priming may not be necessary. We recommend conducting a test beforehand in order to verify adherence.
· Remove the non-stick silicone film from the lower side and apply the membrane to the previously primed surface.
· Press the membrane against the substrate with a brush, from the center toward the edges, in order to prevent bubbles from forming.
· The overlap will be 8 cm, and will be carried out by pressing firmly (once the silicone film is removed) on the upper membrane with a roller.
· TEXSELF 1.5 must not be applied when temperature is below 5ºC. If cold, windy, or humid, heat lightly.
· TEXSELF 1.5 must not be exposed to the elements; the membrane must be protected from the sun. The wear rate when exposed depends on the specific application conditions.
· Installation and measurements will be conducted in accordance with regulations of the UNE 104401 standard.
Roll: 1 m x 20 m
Pallet: 460 m²
· In accordance with the EN 13859-1 and EN 13696 standards. Certified with CE marking No. 0099/CPD/A85/0087
· Certified with No. 12/4905 “Texsa Damp-Proof Membranes” from the BBA (British Board of Agreement).
· Quality System in accordance with ISO:9001

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com