Logotipo Texsa, S.A.

TEXSALASTIC

Flexible two component waterproofing slurry
TEXSALASTIC is a ready-to-use, flexible, two-component slurry. It consists of component A: a special liquid synthetic resin dispersion and component B: powder, a blend of selected filling materials mixed with well-graded sands. A product with unique properties for efficient waterproofing.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
  • Precautions
- The very fine synthetic dispersion endows the compound with excellent adhesion to concrete, natural and artificial stone, wood, steel, galvanized sheet metal, copper, asphalt, marble, plastic surfaces, glass etc.
- The high content of the dispersed synthetic resin particles results in high flexibility for a cement-based material and in the ability to bridge hairline cracks.
- Bridges larger cracks with the aid of reinforcement mat.
- Resistant to water pressure (positive and negative) and offers constant protection from water under pressure or not.
- Resistant to weathering in temperatures from -30oC to +90oC.
- Water vapor permeable.
- Thixotropic, does not flow on vertical surfaces.
- Does not contain chloride or other corrosive salts which cause blooming.
TEXSALASTIC can be used, due to its special properties, for any kind of waterproofing:
- Waterproofing of new and old buildings
- Interior and exterior waterproofing
- Horizontal and vertical surfaces below and above the ground
- Waterproof coatings of potable water reservoirs
- Parking areas, garages and ramps
- Cesspools
- Fully accessible roofings, foundations, support walls
- Water pools, jardinieres
- Basements, tunnels, elevator shafts
- Resistant to UV rays.
SUBSTRATE CONDITION:
The surface application must be clean without any loose materials. The substrate should be slightly wet before the application but free of any water puddles. Substrate temperature must be between +5oC and +35oC.
MIXING:
Mixing ratio:
Α (Liquid):Β (powder) 1:2.6 w/w
The mixing ratio can reach up to 1:4 w/w. for application with spatula.
Pour about ¾ of component Α (liquid) in an empty can.
Add slowly component Β (powder).
Stir constantly and uninterruptedly with a low speed agitator until the mixture is fully homogeneous, without lumps.
Then, add the rest of the component Α into the mixture and stir again.
APPLICATION:
Apply the well-mixed TEXSALASTIC slurry with brush or broom onto the prepared surface in 2-3 layers. Each consequent layer can be applied as soon as the preceding one is dry enough to be touched, i.e., tack-free (ca. 4-5 hours, depending on the ambient temperature).
ADDITIONAL INFORMATION:
- Each TEXSALASTIC layer should be protected after the application against heavy wind and intense sunlight. This way a homogeneous hardening and waterproofing are achieved.
- The thickness of every layer should be max 1 mm.
- The hardening time depends on the temperature conditions. The applied TEXSALASTIC is walkable after 1 day at 20oC. It can be mechanically strained after 3 days. After 7 days it reaches its full hardening and is ready to come into permanent contact with water.
- After the end of the works, wash all tools with plenty of water.
STORAGE
Component A can be stored for at least 12 months from production date in the original pail, in a cool environment protected from frost and direct sunlight.
Component B can be stored for at least 12 months from production date, in its original package protected from humidity.
PACKAGING
Component A (liquid): Cans of 10 kg.
Component B (powder): Sacks of 26 kg.
CONSUMPTION
Application by brush or roller: 1.6 kg per m2 and layer 1 mm thick.
The product is certified according to EN 1504-2 (Concrete Protection Systems), in categories 1.3-Ingress Protection (IP), 2.2-Moisture Control (MC) and 8.2-Increasing Resistivity (IR).
Volatile Organic Compounds (VOC)
EU REGULATION 2004/42: According to Directive 2004/42/EU (Annex II, Table A), the maximum allowed content of VOC (Product Category i / Type WB) is 140 g/L (limits of 2010) for the final product. The final TEXSALASTIC contains max <140 g/L.

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com